KOBE Range Hoods Brillia Series CHX22 SQB-1 Series Model No.: Under Cabinet: CHX2230SQB-1 (30”) CHX2236SQB-1 (36”) Wall Mount: CHX2230
7 - Align and secure Top Vent Cover {P} and 3-1/4” x 10” Vent Cover (removed from rear exhaust) using 14 screws (13 screws taken from 6
8 Ductwork Installation 10. Use steel pipe to connect the exhaust on the hood to the ductwork. Use duct tape to make all joints secure and air tig
9 WALL MOUNT INSTALLATION ***This installation required to have Duct Cover Model No. CH1120DC-1.Preparation before Installation NOTE: TO AVOID DAM
10 4. For Rear 3-1/4” x 10” vent installation only: - Remove attached 6” exhaust and discard. (Figure 10) Keep 13 screws to install vent covers. -
11 Wiring to Power Supply CAUTION: If moving the cooking range is necessary to install the hood, turn off the power in an electric range at the mai
12 Install Accessories 15. Place baffle filters & spacers underneath the hood. (Figure 18) Final Installation 16. Turn power ON in control
13 OPERATING INSTRUCTIONS Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust sp
14 MAINTENANCE For optimal performance, clean the range hood surface and baffles regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE C
15 SPECIFICATIONS MODEL / SIZE For Under Cabinet Application For Wall Mount Application CHX2230SQB-1 (30”) CHX2230SQB-W
16 MEASUREMENTS & DIAGRAMS ***All inch measurements are converted from millimeters. Inch measurements are estimated. ***All measurements in (
IMPORTANT READ THIS FIRST READ BEFORE INSTALLATION 1. Carefully check all contents of packages. 2. Thoroughly inspect the unit for any shipping da
17 ***Hood-Mounting Bracket ***Duct Cover-Mounting Bracket ***Duct Cover Support
18 PARTS LIST MODEL NO.: CHX2230SQB-1 and CHX2230SQB-WM-1 (30”) CHX2236SQB-1 and CHX2236SQB-WM-1 (36”) NO. DESCRIPTION MODEL /SIZE PART NO. 1 6
19 MODEL NO.: CHX2230SQB-1 and CHX2230SQB-WM-1 (30”) CHX2236SQB-1 and CHX2236SQB-WM-1 (36”)
20 CIRCUIT DIAGRAM MODEL NO.: CHX2230SQB-1 and CHX2230SQB-WM-1 (30”) CHX2236SQB-1 and CHX2236SQB-WM-1 (36”)
21 TROUBLE SHOOTING Issue Possible Cause Solution After Installation, both motors and lights are not working. The power is not on. Make sure the c
22 WARRANTY WARRANTY CERTIFICATE In order to obtain warranty service, you must provide proof of original purchase from a KOBE authorized Dealer.
23 THIS WARRANTY WILL BE VOIDED WHEN: 1. Improper installation and failure to follow installation instructions. 2. Any repair, alteration, modific
24 WARRANTY INFORMATION FORM Fill in the blanks and keep this paper with the original invoice in a safe place for future service purpose. 1. Da
KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA www.koberangehoods.com This KOBE hood is made for use in the USA and CANADA on
[ENGLISH] - READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...
1 IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR P
2 What to Do In The Event Of a Range Top Grease Fire • SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the
3 COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box Duct Cover Box (Included in Wall Mount Hood Only) CH1120
4 INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to
5 SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANING OR
6 UNDER CABINET INSTALLATION Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPE
Kommentare zu diesen Handbüchern